The Sanderson FC2 is a blockhugger header for Ford Cleveland and Midland engines. The FC2 fits wider engine compartments and is a good choice for Ford 1954-Up Ford F100 pickups.
NOTE: 3.0″ of clearance from the outside of the starter to the inside of the frame rail (as shown in image below) is required for proper fitment.
- The FC2 header features flanges for 4V cylinder heads. If using 2V cylinder heads, Sanderson’s copper adapter plates, part #2BBLFC are required.
Comes with all hardware necessary for installation.
Engine : Ford 351C and 351M//400
Primary Tube Diameter : 1-7/8″
Collector Diameter : 3″
Weight : 18 LBS / 8.16 KGS
- 16-Gauge Primary and Collector Tube Thickness
- 3/8″ Thick Flange
- Patented Flange Design Requires NO Gaskets
- Tightest Fitting Header Available Anywhere!
- Made in the USA
- Header Bolt Set
- Collector Reducer Set
Sanderson’s Ceramic Coating is recommended for every vehicle application and is the default finish selection choice above. To meet high standards of quality, Sanderson applies a multi-layer inside and outside aluminized ceramic coating in-house and then polishes the coating to a high luster. This aerospace and military-grade technology adds excellent protection to your headers, while offering the benefit of thermal control in your engine bay. It also improves cylinder scavenging of exhaust gases, and increases the longevity of your header investment.
When sitting in driver’s seat and engine in front of you, the LEFT header would be the Driver’s Side on LH drive vehicles; coincidentally, means the RIGHT header is on the passenger side. See the detail image above left that describes engine sides.
NOTE: Image graphic is generic and not exact representation of product.
|Weight (Lbs / Kg)
||18 / 8.16
|1948-1952 Ford Trucks
||CS / RP
|1954-1972 Ford Trucks
CS = Cross Steering; RP = Rack & Pinion
4V vs 2V Cylinder Heads:
Sanderson 351C, 351M/400 headers features flanges for large port four barrel (4V) cylinder heads. If using two barrel (2V) cylinder heads, Part #2BBLFC copper adapter plates are required to ensure proper sealing.
- The Patented Leak-Free Design that Sanderson Headers offer you is the only leak-free flange design on the market … Do Not Attempt To Use Flange Gaskets! The raised flange on the Sanderson Headers will buckle the gasket during tightening and actually cause a leak! Click here for installation procedure.
- Sanderson Headers are NOT emissions legal on pollution-controlled motor vehicles. It is the purchaser’s responsibility to verify local regulations for compliance.
- Wrapping your Sanderson Headers with ANY thermal tape voids your header warranty. The best thermal protection for your headers is our Aluminized Ceramic Coating that is available for every Sanderson Header. Please read our tech article that thermal coatings and header wraps.
Limited 5 Year General Warranty
Sanderson Street Rod Headers strives to supply our customers with the highest quality parts and service available in the street rod industry. In keeping with this, we warrant and will repair or replace, at our option after inspection in our facility, any of our products which are found by us to have failed due to defects in either material or workmanship. This warranty is activated by the return of the Warranty Card enclosed with every pair of headers, and is effective for FIVE YEARS * from the date of purchase as indicated on the original invoice.
This Warranty does not cover products that fail due to improper motor tuning, alteration, disassembly, or damage caused by racing, misuse, neglect, abuse, improper installation and/or accident, or when used on applications for which they were not designed or approved. We are specifically not responsible for the costs of removal, installation, transportation, destruction of other components, inconvenience, loss of time, or other personal damages, or for any other associated costs including the application of aftermarket coatings applied by others. Sanderson Street Rod headers shall not be liable for any and all consequential damages occasioned by the breach of any written or implied warranty pertaining to this sale in excess of the purchase price of the product(s) as found on the original invoice.
WRAPPING HEADERS WITH THERMAL TAPE VOIDS WARRANTY.
* Extremely compact header designs which locate the collector in close proximity to the exhaust ports are very sensitive to engine tuning. Improper air/fuel mix or timing of ignition and/or valvetrain can cause early failure due to excessive heat. For this reason, part numbers CC2 and CC3 are offered with a two-year Warranty period only. All other Warranty conditions apply.