(775) 746-4887

Sales and Support

Mon - Fri: 8:00 AM - 6:00 PM pst

Online store and Helpdesk always open

Sale!

Sanderson BB1MV Big Block Chevy Header Set

$381.00$574.00

The Sanderson BB1MV header fits 1932-48 Cars and Trucks, 1949-63 Chevy cars, 1948-Up Ford pickup, and other applications using the big block Chevrolet 502 Mark V engine.

Clear
Sanderson Headers logo

Sanderson's patented flange design requires no gaskets

The Sanderson BB1MV header fits big block Chevrolet Mark V engines in cars, trucks, and street rods where tight fit and performance are a factor. Virtually eliminating ground clearance problems, the BB1MV hangs down less than 11″ from the center of the exhaust ports on the cylinder heads. The BB1MV header is 2″ tighter to the block than any other block hugger header!

The BB1MV will fit most chassis without a cross member beneath the center of the engine block.

NOTE: The BB1MV is designed specifically for the RH-dipstick on the MarkV 502 engine The difference between the more common BB1 and this header set is the tube routing on the right side header differs slightly to accommodate the dipstick location.

Comes with all hardware necessary for installation.

SPECIFICATIONS:

Engine : Big Block Chevy 502 (Mark IV)
Primary Tube Diameter : 1-7/8″
Collector Diameter : 3″
Weight : 17 LBS / 7.71 KGS

FEATURES:

  • 16-Gauge Primary and Collector Tube Thickness
  • 3/8″ Thick Flange
  • Patented Flange Design Requires NO Gaskets
  • Tightest Fitting Header Available Anywhere!
  • Made in the USA

INCLUDES:

  • Header Bolt Set
  • Collector Reducer Set

OPTIONS:

Sanderson’s Ceramic Coating is recommended for every vehicle application and is the default finish selection choice above. To meet high standards of quality, Sanderson applies a multi-layer inside and outside aluminized ceramic coating in-house and then polishes the coating to a high luster. This aerospace and military-grade technology adds excellent protection to your headers, while offering the benefit of thermal control in your engine bay. It also improves cylinder scavenging of exhaust gases, and increases the longevity of your header investment.

Brand

Sanderson Headers

Sanderson Headers logo

Dimensions

DIMENSIONS:

When sitting in driver’s seat and engine in front of you, the LEFT header would be the Driver’s Side on LH drive vehicles; coincidentally, means the RIGHT header is on the passenger side. See the detail image above left that describes engine sides.

  NOTE: Image graphic is generic and not exact representation of product.

Tube Size1-7/8″
Collector Size3″
LEFTRIGHT
DIM A3½”3¼”
DIM B10¾”10″
DIM C—-—-
Weight (Lbs / Kg)17 / 7.71
Sanderson full length header dimension graphic

Applications

Vehicle Applications:

Steering Type

Pre-1930 Chevy pickupCS
1930-1940 street rods, cars, and trucksCS, RP
1946-1948 cars and trucksCS
1955-1957 Chevy Bel AirStock, 605, 500
1958-1964 Chevy full size cars (Caprice, Impala, etc.)Stock
1948-1952 Ford pickupStock
1949-1954 Chevy pickupStock
1953-Up Ford pickupStock

CS = cross steering; RP = rack and pinion

Engine Applications:

Chevrolet Mark V, 502 big block engines

Install Notes

General Notes:

  1. The Patented Leak-Free Design that Sanderson Headers offer you is the only leak-free flange design on the market … Do Not Attempt To Use Flange Gaskets! The raised flange on the Sanderson Headers will buckle the gasket during tightening and actually cause a leak! Click here for installation procedure.
  2. Sanderson Headers are NOT emissions legal on pollution-controlled motor vehicles. It is the purchaser’s responsibility to verify local regulations for compliance.
  3. Wrapping your Sanderson Headers with ANY thermal tape voids your header warranty. The best thermal protection for your headers is our Aluminized Ceramic Coating that is available for every Sanderson Header. Please read our tech article that thermal coatings and header wraps.

Warranty

Sanderson 5-Yr Header WarrantyLimited 5 Year General Warranty

Sanderson Street Rod Headers strives to supply our customers with the highest quality parts and service available in the street rod industry. In keeping with this, we warrant and will repair or replace, at our option after inspection in our facility, any of our products which are found by us to have failed due to defects in either material or workmanship.  This warranty is activated by the return of the Warranty Card enclosed with every pair of headers, and is effective for FIVE YEARS * from the date of purchase as indicated on the original invoice.

This Warranty does not cover products that fail due to improper motor tuning, alteration, disassembly, or damage caused by racing, misuse, neglect, abuse, improper installation and/or accident, or when used on applications for which they were not designed or approved. We are specifically not responsible for the costs of removal, installation, transportation, destruction of other components, inconvenience, loss of time, or other personal damages, or for any other associated costs including the application of aftermarket coatings applied by others. Sanderson Street Rod headers shall not be liable for any and all consequential damages occasioned by the breach of any written or implied warranty pertaining to this sale in excess of the purchase price of the product(s) as found on the original invoice.

WRAPPING HEADERS WITH THERMAL TAPE VOIDS WARRANTY.

* Extremely compact header designs which locate the collector in close proximity to the exhaust ports are very sensitive to engine tuning. Improper air/fuel mix or timing of ignition and/or valvetrain can cause early failure due to excessive heat. For this reason, part numbers CC2 and CC3 are offered with a two-year Warranty period only. All other Warranty conditions apply.

Downloadable Version

 

Share your thoughts!

Let us know what you think...

What others are saying

There are no contributions yet.

×

Login

Continue as a Guest

You may also like…