(775) 746-4887

Sales and Support

Mon - Fri: 8:00 AM - 6:00 PM pst

Online store and Helpdesk always open

Sale!

Sanderson FF427 Ford FE Header Set for 1953-Up Pickups

$389.00$629.00

The Sanderson FF427 header set fits 1953-Up Ford F-Series pickups using the Ford 332-428 FE engines.

Clear
SKU: SDH-FF427 Category:
Sanderson Headers logo

Sanderson's patented flange design requires no gaskets

The Sanderson FF427 header fits Ford big block FE engines in 1953-Up Ford F-series pickups. The FF427 offers excellent clearance around the engine and chassis components, plus 1-3/4″ primary tubes and a 3″ collector for big power gains. Available for both standard and Cobra Jet / GT cylinder heads.

Comes with all hardware necessary for installation.

PLEASE NOTE:

There are a very small number of applications (always Camper Special, but not every Camper Special) that may have driver side clearance issues at the steering box. Please review the “Camper Special” information tab. “If” the standard FF427 driver side header set has clearance issues we recommend exchanging the driver side header ONLY for part #SDH-FF393. However, we now offer a specific header set for Camper Special applications, part #SDH-FF427CS. Please contact us by phone or through the Helpdesk regarding this exchange.

SPECIFICATIONS:

Engine : Big Block Ford FE (332-428)
Primary Tube Diameter : 1¾”
Collector Diameter : 3″
Weight : 20 LBS / 9.07 KGS

FEATURES:

  • 16-Gauge Primary and Collector Tube Thickness
  • 3/8″ Thick Flange
  • Patented Flange Design Requires NO Gaskets
  • Tightest Fitting Header Available Anywhere!
  • Made in the USA

INCLUDED ITEMS:

  • Header Bolt Set
  • Collector Reducer Set

 OPTIONS:

Sanderson’s Ceramic Coating is recommended for every vehicle application and is the default finish selection choice above. To meet high standards of quality, Sanderson applies a multi-layer inside and outside aluminized ceramic coating in-house and then polishes the coating to a high luster. This aerospace and military-grade technology adds excellent protection to your headers, while offering the benefit of thermal control in your engine bay. It also improves cylinder scavenging of exhaust gases, and increases the longevity of your header investment.

Brand

Sanderson Headers

Sanderson Headers logo

Dimensions

DIMENSIONS:

When sitting in driver’s seat and engine in front of you, the LEFT header would be the Driver’s Side on LH drive vehicles; coincidentally, means the RIGHT header is on the passenger side. See the detail image above left that describes engine sides.

 NOTE: Image graphic is generic and not exact representation of product. 

Tube Size1¾”
Collector Size3″
 LEFTRIGHT
DIM A4½”4½”
DIM B6″6″
DIM C—–—–
Weight (Lbs / Kg)20 / 9.07
Sanderson full length header dimension graphic

 

Camper Special

We offer a variation of the FF427 header set (part #FF427CS) for “specific” Ford Camper Special F-Series pickups using the Ford FE (332-428) engine.

The FF427CS combines the standard FF427 passenger side header with the FF393 driver side header to compensate for the narrow frame rails and larger steering gear that appears on “some” Camper Special trucks.

NOTES:

  • The designation “Camper Special” does not mandate the use of the FF427CS header set
  • All Camper Special trucks are not the same
  • Not all Camper Special trucks require the FF427CS header set. In most instances the standard FF427 fits perfectly
  • The need for the FF427CS header set is not consistent across model years or the “Camper Special” designation
  • If the truck uses a much larger Bendix steering gear, the FF427CS is the correct choice

Install Notes

 

  1. The Patented Leak-Free Design that Sanderson Headers offer you is the only leak-free flange design on the market … Do Not Attempt To Use Flange Gaskets! The raised flange on the Sanderson Headers will buckle the gasket during tightening and actually cause a leak! Click here for installation procedure.
  2. Sanderson Headers are NOT emissions legal on pollution-controlled motor vehicles. It is the purchaser’s responsibility to verify local regulations for compliance.
  3. Wrapping your Sanderson Headers with ANY thermal tape voids your header warranty. The best thermal protection for your headers is our Aluminized Ceramic Coating that is available for every Sanderson Header. Please read our tech article that thermal coatings and header wraps.

Warranty

Sanderson 5-Yr Header WarrantyLimited 5 Year General Warranty

Sanderson Street Rod Headers strives to supply our customers with the highest quality parts and service available in the street rod industry. In keeping with this, we warrant and will repair or replace, at our option after inspection in our facility, any of our products which are found by us to have failed due to defects in either material or workmanship.  This warranty is activated by the return of the Warranty Card enclosed with every pair of headers, and is effective for FIVE YEARS * from the date of purchase as indicated on the original invoice.

This Warranty does not cover products that fail due to improper motor tuning, alteration, disassembly, or damage caused by racing, misuse, neglect, abuse, improper installation and/or accident, or when used on applications for which they were not designed or approved. We are specifically not responsible for the costs of removal, installation, transportation, destruction of other components, inconvenience, loss of time, or other personal damages, or for any other associated costs including the application of aftermarket coatings applied by others. Sanderson Street Rod headers shall not be liable for any and all consequential damages occasioned by the breach of any written or implied warranty pertaining to this sale in excess of the purchase price of the product(s) as found on the original invoice.

WRAPPING HEADERS WITH THERMAL TAPE VOIDS WARRANTY.

* Extremely compact header designs which locate the collector in close proximity to the exhaust ports are very sensitive to engine tuning. Improper air/fuel mix or timing of ignition and/or valvetrain can cause early failure due to excessive heat. For this reason, part numbers CC2 and CC3 are offered with a two-year Warranty period only. All other Warranty conditions apply.

Downloadable Version

 

Share your thoughts!

Let us know what you think...

What others are saying

There are no contributions yet.

×

Login

Continue as a Guest

You may also like…